American MGB Association

North America's oldest, largest and best club for all year MGBs, MGB-GTs and Midgets!!  Established in 1975.

 

American MGB Association

 Subscribe Message Board

Subscribe Blog

 Subscribe Photo Gallery

WELCOME TO THE AMERICAN MGB ASSOCIATION
for all year MGBs, MGB-GTs and Midgets

Established in 1975
 

5433 N. Ashland Ave.
Chicago, Illinois 60640  U.S.A.
Phone/Text: 773-769-7084

email:
info@mgclub.org

American MGB Association on Facebook American MGB Association on Twitter

                     


Credit Card/PayPal Form  Secured Order Form   Members Only Join/Renew-Application  Membership Benefits
Home   Past Shows/Photos  Calendar of Events   Member Stories/Articles  Tech Tips   Membership Benefits   Ads/Links     Membership Items   Email   Classifieds   Member Car Photos   News/Editor   Regalia/Club Store   Message Board  Club Blog  Ad Rates  

 

fff


What We Offer
Join the AMGBA!

Home
Events Calendar
Past Shows/Photos
Classified Ads
Member Stories
Member Photos
Technical Section
Editor & News!

Club Regalia/Store
Message Board
Club Blog
Membership Items
Secured Order Form
Credit Card/PayPal
Members Only

Sponsors/Ads/Links
Ad Rates & Info
Officers
Networks/Groups
Meet Info
Contact Us

 

 

 TECH TIPS

Changing the Distributor
this is an excerpt from the articles appearing in the OCTAGON

also see upkeep and performance hints on our message board at board.mgclub.org
and on our Facebook group at
www.facebook.com/groups/americanmgbassociation

Changing the Distributor
by Art Isaacs

Changing the distributor on a B is fairly easy, especially if you have good mechanical ability.

Unlike American cars, the Lucas (or replacement aftermarket) distributors can only go in one way. They don't have gears on the bottom, but keys and slots that are different from side-to-sided, so the rotor will always point in the correct direction. The trick is to reasonably align the number 1 spark plug wire as it was originally.

Also, some aftermarket distributors require reusing the drive (keyed coupling) from the old distributor. Not a daunting task, but the roll pin that retains it has to be punched-out and the coupling properly aligned on installation to the new unit. It should be keyed to the shaft, so that becomes easy.

Little tricks:

- Mark all the park plug wires on the cap. If you don't have the electrician's numbered bands, a piece of masking tape with the number written in dark ink (Sharpie or gel pen) number works fine. Make sure the number one plug wire is especially clear.

- Mark the block where the number 1 plug wire is positioned on the distributor. Just helps to get the new distributor positioned so the car will start to be able to set the timing with the light.

- Take at least 2 photos of the old distributor before removing it. One with the cap on (so you can see the #1 plug wire and Vacuum advance pot positions) and the other with the cap off (to see the rotor direction).

- Remove the cap, primary leads (with the CEI you have to also remove the module), the 2-bolt clamp that retains the distributor and just pull it out.

- Remove the clamp from the old distributor (single bolt length-wise across the split side of the clamp) and check the clamp is not bent and the bolt is free and can be adjusted. Repair or replace as necessary.

- Reinstall the retaining clamp to the block with the adjustment bolt still somewhat loose.

- Install the new distributor with the rotor in place. The rotor should automatically line-up as the keys in the bottom of the distributor should only fit the same way as the old one did. Determine where the #1 wire would be (that can vary between distributors relative to the vacuum advance pot) and set the body of the distributor so that it is in the same place, either using the photos you took or the mark on the block.

Now, depending on which way you went on the replacement distributor determines what you do next. I'll follow the 45D4 installation with a Pertronix kit as that's what I'm most familiar with. The others, being completely different, should come with full instructions, but will only differ in the controls and associated wiring.

With the distributor in place, rotor and cap off, install the Pertronix unit. A sensor cap goes over the cam that actuated the points on the shaft just below the rotor. 2 screws that used to hold the points in place now secure the reader unit to the plate.

The kit comes with the wires that replace the primary lead and power source and they have to be snaked through the hole in the lower distributor body the primary lead had gone through. Instructions are provided. Make sure in ordering the distributor and Pertronix kit that they match by model. The kit for a 25D4 will fit the points plate, but the wiring harness is very different and won't fit. And caps and rotor are not interchangeable.

Fit the cap, wires and vacuum advance line and start the engine. Once warmed-up, remove and plug the advance line, adjust the idle, fix your timing light and set the timing. Once set, adjust the idle, tighten the clamp, reconnect the vacuum line* and done.

My personal advice here is a reminder that, with a turbo, the vacuum advance may be hooked up differently or bypassed entirely. The intake manifold is now under pressure from the turbo, so it won't work conventionally. With a draw-through set-up (carb before the turbo) it can use fittings on the carb to work pretty much normally, but if you have a blow-through set-up (carb after the turbo), the carb is now under pressure, so no vacuum.

This could influence your distributor kit purchase, as it may be best to get a fully mechanical advance type distributor, like the one from Crane. Check and make sure what you have before buying anything.

Moss sells their supercharger kit, so see what distributor they use on that. Also, sources, like JEGS or Summit Racing carry aftermarket distributors and Pertronix kits for the MGB that may be better suited to your application.

They routinely work with supercharged and turbocharged racers and hot rods.

Safety Fast!
Art Isaacs


More tech items at www.mgclub.org/mgtech.htm, at https://www.facebook.com/groups/americanmgbassociation
and www.facebook.com/americanmgbassociation and on our message board at https://mgclub.org/smf/.


 

Members Only
Services:
Members Login

On-Line Octagons
On-Line eOctagon
Local Chapters
Parts Exchange
Technical Staff
Technical Services

Renew
Member Services
Submit Classified

Message Board
Club Blog
Photo Gallery

member
recommended:

Repair Shops
Body Shops
Parts Suppliers

American MGB Association on Facebook

American MGB Association on Twitter
 

 

 

 


Credit Card/PayPal Form  Secured Order Form   Members Only Join/Renew-Application  Membership Benefits
Home   Past Shows/Photos  Calendar of Events   Member Stories/Articles  Tech Tips   Membership Benefits   Ads/Links     Membership Items   Email   Classifieds   Member Car Photos   News/Editor   Regalia/Club Store   Message Board  Club Blog  Ad Rates  

 

  AMGBA Privacy Policy | AMGBA Website Terms of Use
1997-2019 All Rights Reserved - American MGB Association.